I've been working on this for a while now and decided to start a thread on it here. I'll just copy and paste my updates from another site to get this thread up to date...
UPS dropped off the tires I plan to use for this build today. I went with 21" M.C. rims which will hopefully be in later this week. The tires are Shinko SR244 Dual Sports, these things are beefy!
I measured the outside diameter real quickly, comes out to a little over 27.5". It actually might be a little bigger once they are mounted on the narrower rims I have on the way...
And just for fun, here's one next a 26" Felt Quick Brick...
The picture doesn't really do justice to how much bigger these are than the Q.B.'s
The rims showed up today, They're used but in good shape other than some paint chipping, double walled, with large spoke holes. I didn't take a picture with a tape but the outside diameter of the lip is right at 22". This rim size is 1.6" wide but since they're so thick the outside thickness is about 2.5"....
I stuck one of the tires on a rim and measured the overall o.d. which now is a little over 28"!
I didn't measure the width of the tire on the rim because it's not inflated yet but as it sits it is closer to 2.75" wide...
Overall I am very pleased with these and can't wait to start building.
I ordered some 9 gauge spokes for the rear wheel from Newsonsportec in Taiwan. They arrived today and thankfully I did my calculations correct. Here they are packaged up, the hub was offset so it required some dishing...
They make the 11 gauge spokes on another bike look pretty thin...
All laced up, I still need to true the wheel...
I'll hopefully be ordering tubing for the frame at the end of May and will have some real updates soon.
So I've been drawing up my frame and had some questions. Through looking at different pictures of old bikes, specifically Indians, I have noticed there seem to be some with shorter wheel bases. There are the street bikes with all of the bells and whistles that have quite a bit of room between the rear tire and the seat tube and there are the stripped down racers that look like there is only a couple inches. The Indian below is one the shorter looking bikes and has the looks I am going for on my build. Can anyone confirm if there are shorter B.T.R.'s or are these just visual illusions from different pictures. If there are shorter bikes, does anyone know the wheel base on them?
Here is a Cyclone that I based my drawing off of, I changed the bottom tube and scaled it to fit 27" tires.
I know that scaling it down will make the wheelbase shorter but it seems like it shouldn't have changed as much as it did. I also changed the head tube angle to give it more trail which pushed the front tire out more. What I'd like to know is even with the trail I have will the short wheel base make the bike squirrely at speed? I can probably add an inch or two in the rear triangle but that still only puts it at 52" where as I've read on here 55"-58" is best. I don't want to lose the look of the compact Indian above so without going to larger tires I don't see another way to make up the wheel base. On a side note, if anyone has more info on the Indian I'd greatly appreciate it if you shared because it looks like it has modern tires and rims which I think are the same size as I'll be running yet still looks proportionate to the frame.
I played with the drawing a little more and stretched both the front and back out till it was at 55", I also lowered the middle tube leaving an even 5" for the tank, I think this will be it, time to order tube...
Finally ordering some tubing, 1" and 3/4" .120 wall Dom, I layed out the frame on the floor to help with making the bends, will hopefully see some real progress in the coming weeks...
Got the metal, before I start on the frame I wanted to get the fork squared away since it's the most complicated part. This way I can still tweak head tube angle and geometry if the fork ends up a little different than on paper.
Got the main tubes on the forks tacked on, I also made some axle tubes out of 3/4" tubing sleeved inside of 1", than drilled and tapped with set screws.
The wheel pictured is the hub I am using for the front, it is off of a Honda XL185, I feel more confident with a motorcycle brake in the front not to mention the whole wheel with tire was $45.00, I'll use this rim and tire for mock up than lace up the other black rim I have later on. Now that the mounting points on the fork are complete I started working on the main part of the frame too. Hopefully I'll have it all tacked this week...
Finished tacking the middle frame together. Up next, make the rear drop outs and I have to work on a jig to keep the wheels in line so I can make the rear triangle.
I got lucky and found an aluminum white board track that cradles my tires perfectly, made some uprights to hold the frame and put it on a table. No more working on the ground. I also got the upper shock mounts tacked but will probably redo them...
Well, I made rear drop outs and set up the triangle but I don't like it so I am going to rotate the triangle a little to raise the overall height and shorten the wheel base, I'll also move the head tube to make sure everything stays level and geometry is correct. It turns out the shocks I have are going to be too soft for this set up so I'll probably get mountain bike coilovers like these which will hopefully stiffen it up.