making old lights LEDlights

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I Googled "bicycle led light conversion" and got a dozen or more hits with pictures, videos, etc. of different approaches to converting lights to LED.

sometimes you can get lucky with the vintage slender bullet-type lights and a LED flashlight will drop right in, with the handle part cradled perfectly in the battery tray, and the lens filling in the front open part of the light housing. Almost looks like it was made to be that way. No conversion necessary, just a drop-in.

teqetu5u.jpg


qynybyza.jpg


2012-10-05_17-55-43_665.jpg


8152172480_a2a9663554_b.jpg
 
This is one I did on my panther and used a old bulb and added a led to it I dident want to rune the light in any way. This is what I used got it for a buck at the dollar store just took it all a part for the goodies

6DDCE960-AD1C-4C50-8BAA-15F9FD9D4DDE-709-0000007D25D24A24_zps756d6068.jpg

6E31504E-485E-471C-BD73-3460254E7F04-709-0000007D40E31742_zps152765ba.jpg

D06A7DD2-9C18-4501-8D9A-708443A433E4-709-0000007D391FAE49_zps7c4c74e4.jpg

That's the led in the bulb
D8C75499-308C-402D-89F8-76F0829235BD-709-0000007D324B6967_zps1f555f94.jpg

9F0B8D6E-AB29-4B7C-BA2A-60C7857572A6-1421-000000E870B67C35_zps8a7b3288.jpg
 
Here is how I convert standard 5 3/4" H4 motorcycle bulbs to LEDs.

Start out with $5.00 19 LED 4-mode head lamp from Ebay.

19led_headlamp.jpg


If you unscrew the lens and remove the battery holder, the circuit boards have tiny screws holding them in. The small one has the push button.

hl_conversion01.jpg


hl_conversion02.jpg


Wired in a battery holder and momentary push button switch and mounted the boards to a plastic dust plug from another H4 bulb. Haven't found a source for these but you can make your own out of plastic or take apart an H4 halogen and mount the boards to that using some plastic to isolate them from the metal. I colored the LEDs with an orange sharpie because the light was too blue for my liking.

hl_conversion03.jpg


hl_conversion04.jpg


The chrome reflector from the head lamp is installed over the LEDs in the reverse direction from original. Battery holder is velcroed to the headlight housing. Switch is fitted to hole where headlight wiring would normally go.

hl_conversion06.jpg


hl_conversion05.jpg


hl_conversion07.jpg


This is a standard H4 motorcycle bulb. Some have a smaller opening in the reflector that only accommodates the small portion of the bulb.

hl_conversion08.jpg


This is the headlight on my Basman. With this bulb, it's plenty bright to ride in the dark on the street and definitely stands out to oncoming traffic. I tried brighter cree LEDs but they overwhelm the lens and the light just scatters too much.

basman012.jpg


Here's a nighttime picture of the same conversion on one of my other bikes.

630_42.jpg
 
Used the same light, switch and battery and velcro as the Arias triangle light as I did on this old 4 1/2" light on the MURDER bike. I welded two pieces of flat stock into the housing to give the battery and LED board something flat to velcro to. LEDs were from a gutted 3 dollar flashlight from the local Harbor Freight.
486524_520531111337457_1573687521_n.jpg
 
In this light the entire glass piece is the bulb with the filament and reflector integrated. Has anyone tried drilling our holes in these and feeding the LED's into it that way?
freestuff012_zps5cd65892.jpg
 
kim_dude said:
In this light the entire glass piece is the bulb with the filament and reflector integrated. Has anyone tried drilling our holes in these and feeding the LED's into it that way?
freestuff012_zps5cd65892.jpg

Did one for my FatBob build:

LukeTheJoker said:
I found an old sealed beam headlight and one of the spare led lights I bought a while back (half price $3.50 Supercheap auto for those in Aust)

DSC00145 by LukeTheJoker, on Flickr
a little judicious grinding with a diamond tile blade. PLEASE USE SAFETY GEAR IF DOING THIS! Please use a dremel or something similar if you have one, as it would be far safer than the grinder with a diamond blade!

DSC00146 by LukeTheJoker, on Flickr
Ok, so it didnt come out perfectly round as the last little bit broke before I finished but it followed the cut line around and so was very close and I just hot melted the leds in.

DSC00147 by LukeTheJoker, on Flickr
Works well!

DSC00148 by LukeTheJoker, on Flickr

Hope that helps...

Luke.
 
LukeTheJoker said:
kim_dude said:
Lens got too hot cutting through it with the dremel and cracked. Back to the drawing board. :?
Ouch! :shock:
Do you have another one?

Luke.

Nope, I'll just get some sort of plexi lens cover and drill out a reflector. I don't have one that big but I'll think of something.
 

Latest posts

Back
Top