Rat Rod Blades Challenge 2021 - Build thread

Rat Rod Bikes Bicycle Forum

Help Support Rat Rod Bikes Bicycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Old Uncle
“Anyway, I seem reluctant to glue and pin my knife”

the deed is done.

And I figured out why I was reluctant to move forward. Thanks to Folgers-the good coffee.
15F9DEEE-CCCB-47AE-801E-9F213D267ACB.jpeg
 
Last edited:
***I'm reposting this here, originally put it in the 'discussion' thread. Yes, I'm old.**

Goodwill Hunting Knife

Opened up the Tandy Leather Co. sheath kit this morning and got a start on it. First thing I did was a 'dry fit' of my blade in the sheath. A little tight, so I did what I'd been thinking of doing anyway, and took the sharp corner off the back end of the blade. Has better flow now, and less of a 'cleaver' kind of look.


151235958_838771403338870_5846430994565658934_n.jpg


151224168_701630157195028_1112552824398401548_n.jpg


I used some virgin olive oil to darken or 'patina' the veg-tanned leather. Then grabbed the stamps I had purchased at Tandy and the wooden mallet, and embossed some design onto the sheath.

151609801_174780237751279_1484798187431774444_n.jpg



151201374_237824607881119_3703360559650426963_n.jpg



You can see the original color on the right, which will be the inside of the sheath, and then what happened after I applied about 3 coats of oil to the leather on the left.


151191119_2761108910872592_3667817281708100786_n.jpg


I found that I needed about a dozen strikes with the mallet to get an impression on the leather that was deep enough to be seen. In the photo above, I had only hit it about 6 or 7 times. Here are the pieces drying in the sun. The oiled leather lightens as it dries, so I will likely add more this afternoon.


151527207_285358156271565_7793456662996151858_n.jpg



151863037_426745221967736_7822449123198645328_n.jpg


2019 Builds in RRB Build-Offs:
" Helen Wheels" " Trans-MIG- RaT " " RaTsberry Buffet"
 
Goodwill Hunting Knife

Really fun day in the garage / workshop! This Tandy Leather Co. sheath kit only cost me $7.00, and it made the project go so smoothly. The waxed thread is cool that you stitch the front and back together with. My wife and I sat out in the garage (faces south, nice sunny day) and she told me stories of all the clothes and stuff she used to sew as a kid and teen. Sewed all her own clothes. It was the '60s, not uncommon in those days.

My favorite story was the one where she had just finished this mini skirt and matching sleeveless blouse. Father Mike from their local parish was over for coffee visiting with her mom at the kitchen table. Barb came bouncing down the stairs in her new outfit, excited to show it off on a Saturday night downtown.
As she hit the bottom step, and the priest caught a glimpse of her heading for the door, he quiried, "Dorothy, you're not going to let her out looking like that are you?"
Barb flushed a bit, but kept moving, not waiting for her mother to reply, or change her mind.

I used a combination of the olive oil, some leather conditioner, and brown shoe polish to achieve kind of a 'sunburst ' western look on the sheath. The shoe polish settled in to the grooves of the embossed designs and then I was able to wipe the excess away, while leaving some of the brown hue behind.

I might be done with this knife. Pretty much on schedule of an OJ build. I do have a belt I bought at a thrift store that is too long for me. I might shorten it, do some stamping on it, and polish it up to match the knife holder. We shall see.
151863037_426745221967736_7822449123198645328_n (1).jpg


151271578_1149798878785031_1625543247200100897_n.jpg

151405681_912359512641052_6878276888912770254_n.jpg


151353882_348736456253679_1380929245590147887_n.jpg


151924790_2904095666514759_1848708139258690457_n.jpg

151235989_2795323037358257_3831004475792063413_n.jpg

151150534_2853906494869711_5565775230954913771_n.jpg
 
Padauk Basher

Day 2

Cutting scales down
20210217_211803.jpg


Shaping
20210218_013019.jpg


More shaping
20210217_223518.jpg


Little more shaping and some sanding
20210218_012354.jpg

20210218_012327.jpg

20210218_012339.jpg


Apart from being toxic and giving you orange boogers, the padauk is pretty nice work with.

Using steel pins instead of brass is annoying. I dont have a belt sander, so the only thing I have capable of grinding them down is the angle grinder. Had to get real precise with it to get them flush without losing too much wood as well.

I still have to clean some epoxy off the blade, and work out some nicks where I caught it with the rasp.

And there's a few spots I missed sanding so I'll have to go down a few grits then bring it back up.

The knife is a real little guy, much smaller than I envisioned before it was together. So I'm gonna have to rethink my plans for decoration a bit, and see what I can come up with. I don't want to leave it just plain.

It also doesn't fit in it's sheath any more. The makers of the blank intended for the finger guard to be left exposed, but I wanted the scales to extend over it for the look and comfort. But it does mean it's now too fat for the strap to close. So I'll either have to modify it or make a new one.
 
Last edited:
@Verrt , nice work! Great handle shaping, and all by hand.
My son and I looked at Padauk as an option for a stave shell snare build. I have always liked the look. Has an elegant look with your highly polished (stainless?) blade.

Just for purposes of scale (knife pun intended), what is the length of the blade on your knife?
 
@Verrt , nice work! Great handle shaping, and all by hand
Thanks! Though I had some mechanical assistance.
You could get to this point pretty easily with just the coping saw and middle rasp.
20210218_075322.jpg


I think 440 stainless? Says what on the packet it came in. Can't be bothered to go back to the basement again.


Just for purposes of scale (knife pun intended), what is the length of the blade on your knife?
20210218_084733.jpg
 
Friction Folder
Did a little more work on the blade and tried to cut a slot in this piece of cherry for the handle. That failed so I cut all the way through, and will now open up some space for the blade before pinning and gluing it back together.
mince I know it all fits, I will harden and temper the blade before assembly.
Does anyone have any experience with old Nicholson files? Is a Water or an oil quench preferred?
0162BD5C-FCA5-4ADD-9686-6A4F5E36A2FA.jpeg
 
Bike-nife

How did I get talked into this challenge? I know nothing of this stuff. Anyway.. it's not going well so far. Later I will post pictures of some lame attempts with no progress.

I attempted to enlarge existing .125” holes to .390” for chainring bolt clearance using lots of oil and a ceramic tile bit. Did not work.

6b4d76917f90f6a7afa86e6487b04159.jpg


Made a nice chamfer tho?

Called a machinist friend this morning. He said “I’ve got carbide everything. Bring it over”. So I’ll try to get there this week and we’ll go riding too.
 
Last edited:
Goodwill Hunting Knife
Found a display spot for the GHK. Built / refab-ed this table centerpiece a couple years ago; also made from a Mesquite tree.

The knife rests on it's base. Deadliest 'table knife' known to man.
20210222_095220.jpg

20210222_095310.jpg
 

Latest posts

Back
Top