Search results

Drilled out thr cap and test fitted the fuel hose. Have to find the fittings for the hose but its coming along. As for the JD bottle, it fits VERY nicely. Im a little worried about the vibrations in general. Still contemplating on what to use for a solution.

Not much done. Doing a lot of cleaning in storage lately. Got the brackets for the front drilled. Need to get a longer axle stud due to clearance issues. Also put in a JD bottle as another gas tank/extension. Going to hide the boost bottle under the seat ... hoping it will work. JD Bottle...

as of now, the headlight it ready to be wired up to an on/off switch which I am also wiring to the tail light (I'm taking the dual light headlight, LED mod with one of the LED's as a constant "on" when I trigger the headlight and a toggle "off/on" - with it naturally "off" and "on" when...

It's pretty bright and I know for a fact someone will be able to see this coming at them. As for that trim ring that was in the flash light originally, I'm not really sure what happened to it, but when I opened up the housing to get to the LED's, it warped somehow. It has been VERY sunny lately...

Got some work done on the headlight. Soldered the wiring, but lost one of the LED bulbs along the way. Might get another one since they are only a dollar lol. Imo, came out better than I thought it would.

More shots of the fork. The last shot is how much i had to grind (not much really but fits perfectly). Need to line up where im gonna drill the holes for the fork/wheel plate and then get bolts. Also got around to drilling a hole for the LED headlight mod. Need to borrow or buy a...

Got more work done on the forks. Found the other set of these centering spacers i had. Grinded out the mountain bike fork so that they would fit.

And that was me using my shirt to scrub it off!!!! The swirlies you see within the botch, that was from the steel wool, I thought I could clean it off. It most likely just made it worse.

Well this sux.... not sure why but I used some glue to help with the led mock up... BAD IDEA. Was trying to clean it out, and well, this is what i ended up doing to this PERFECTLY good light housing :(

Started on the springer fork. Almost done, just need the brackets and spring. Debating on headlight placenent though.

Started on the headlight mod. Going from bulb to led (this was on the OCC bike, figured it would help with the ugly front i have atm). Previous bulb: Led: The back piece is large as all heck. So im going to buy the bullet hl w/high beam setting (use for brake light) mate the wiring with...

Got the seat mounted, might leave it as is, works perfectly or put in a bolt to keep the seat from tilting (all thats really holding the seat to the seat mount is the seat springs). Got the chain clearance i need, but wondering if it'll bee too much stress on the steel staps. Might have to...

Got the seat mounted today. Have to secure the front of it and add the cross brace that was on it originally but getting close. Found some steel straps at OSH. Fairly thick, about same as the steel plate. Lucked out today too. The small bolt holes by the rear dropout were threaded, plus were...

I was looking at my bike again, i dont like the negative space it has behind the seat post. Hopefully i can find something the size of this grease container, going to make a false oil bag and use it for more fuel ;):D Maybe add in an actual battery box (not sure what kind of battery ... a...

... was doing mock work on the seat... coupke seconds im inside putting sone brackets on abd THUD!!! Bikes on its side. Lift her up and find theres a dent on tge gas tank !!:mad::arghh::eek:

Cleaned up a little and got a better view of things - mock update While cleaning, came across some air compressor brackets. Was shocked when I found a perfect fit with old car bolts and some off of the occ bike. Did a seat mock... not sure how Im going to bend the brackets. Im at about a 39°...

For now i have to play the waiting game yet again... ran out of funding lol. When i gey enough, im going to start on the extension. Then need to get the MM adapter. Tried to configure the kit adapter ... not happening, it works but up until maybe half way, then the spoke mount gets in the way...

Thanks. I went to get some bolts for the stem (swapped for the tops of the occ riser), too long hut better than too short lol. Have to swap them for ahorter ones. Trying to find a way to get the 1/8" steel plates, seen straps that look like they might work but not as tall as i need them. Im...